2011, 2012 FORD 3.5L F-150 (Twin Turbo) ECOBOOST Pre-Loaded Programmer #3015 by SCT

SCT’s new Ford F-150 Ecoboost custom tuning package adds custom tuning support for the new 2011-2012 Ford 3.5L Twin Turbo F-150. In addition to this new Ford F-150 custom tuning package, SCT has also released an updated tune revision for the SCT SF3 (Part #: 3015) pre-loaded devices. This tune revision includes 3 Pre-Loaded Performance tune files (87, 91 and 93 Octane) and a wide range of User Adjustable Tune Options such as Axle Ratio, Tire Size and adjustable Shift Points!

Starting with an impressive 365 Horsepower & 420 ft-lbs of Torque direct from the factory, SCT's pre-loaded, dyno proven tune files add up to 51 Rear Wheel Horsepower and 108 ft-lbs of tire shredding Torque using the pre-loaded 93 Octane tune. That means an addition 60 Horsepower & 129 ft-lbs of torque at the flywheel is added to your truck in a few minutes, without even getting your hands dirty!

Don't want to run 93 Octane fuel on a daily basis? No problem! Simply install the pre-loaded 87 octane performance tune and add an impressive 35 Rear Wheel Horsepower & 66 ft-lbs of Torque while saving some money on the lower octane rated fuel.

In addition to this newly unleashed power, SCT's pre-loaded Ecoboost programmers also remove the vehicle’s top speed limiter, raises the RPM Rev Limiter, increases your truck's throttle response & shift firmness, all while maintaining the vehicle’s factory drivability & reliability.

What Customers are Saying about their new Ecoboost SCT Tunes / Devices!

"Thanks SCT, Loaded up and went and got a tank full of 93. Running the 87 tune now. Shifts took a little getting used to but seems to have a good bit more giddy up."

"Loaded perfectly and runs fantastic! Switching to the 93 tune this weekend. Cant wait!"

"Also I love all the options that this device has there is so many things I can change with shift points exc. Leaps and bounds above anything else on the market right now hardware-wise!"

"Man I love this tuner! I cant keep my foot out of it today. It acts completely stock (better then stock). Drives so nice Then you hit the go pedal and it just takes off."

"Love the tuner, best money ever spent!"

INSTALL THE SOFTWARE

* With the Tuner unplugged we need to install the SCT Device Updater Software.
(Software found on the dowloads section of the tech support page)
* Let it install in the default location, clicking next, next, next until you get to Finish. You should see a New Icon on your desktop for the SCT Device Updater Software.

INSTALL THE DRIVERS

* Once installed, Plug in the Tuner and wait for the Found New Hardware Wizard to Pop Up.
* It may ask you "Can Windows connect to Windows Update to Search for Software?" If it does, click "No, Not at this Time" and press Next.
* At the Next Window, Select "Install Software Automatically (Recommended)" and click Next. Windows will search and Install the drivers for your device, Click Finish to Finish the Driver Installation.
* NOTE: If a Found New Hardware Wizard did not pop up, and you get an error in the next step, go to the section for Installing Drivers Manually.

SAVING A COPY OF YOUR STOCK FILE

* Now that the drivers are installed, open the X3/Livewire Updater software. There will be a new Icon on your desktop. (Yellow, Orange and White.)
* Once opened, click on the button labeled: "GET STOCK FILE" this will open the window asking where to save your stock file.
* Browse to the location of your choice.
* This will save your files as Stock.lbu and Flash.lbu
* The current format of the file WILL NOT load back onto the tuner as is. If a situation arises where you need to use this stock file, you will need to contact SCT Tech Support to assist you.

SCT Quick Start Guide: